Scrapy defaults are optimized for crawling specific sites. These sites are often handled by a single Scrapy spider, although this is not necessary or required (for example, there are generic spiders that handle any given site thrown at them).
In addition to this “focused crawl”, there is another common type of crawling which covers a large (potentially unlimited) number of domains, and is only limited by time or other arbitrary constraint, rather than stopping when the domain was crawled to completion or when there are no more requests to perform. These are called “broad crawls” and is the typical crawlers employed by search engines.
These are some common properties often found in broad crawls:
- they crawl many domains (often, unbounded) instead of a specific set of sites
- they don’t necessarily crawl domains to completion, because it would impractical (or impossible) to do so, and instead limit the crawl by time or number of pages crawled
- they are simpler in logic (as opposed to very complex spiders with many extraction rules) because data is often post-processed in a separate stage
- they crawl many domains concurrently, which allows them to achieve faster crawl speeds by not being limited by any particular site constraint (each site is crawled slowly to respect politeness, but many sites are crawled in parallel)
As said above, Scrapy default settings are optimized for focused crawls, not broad crawls. However, due to its asynchronous architecture, Scrapy is very well suited for performing fast broad crawls. This page summarizes some things you need to keep in mind when using Scrapy for doing broad crawls, along with concrete suggestions of Scrapy settings to tune in order to achieve an efficient broad crawl.
Concurrency is the number of requests that are processed in parallel. There is a global limit and a per-domain limit.
The default global concurrency limit in Scrapy is not suitable for crawling
many different domains in parallel, so you will want to increase it. How much
to increase it will depend on how much CPU you crawler will have available. A
good starting point is
100, but the best way to find out is by doing some
trials and identifying at what concurrency your Scrapy process gets CPU
bounded. For optimum performance, you should pick a concurrency where CPU usage
is at 80-90%.
To increase the global concurrency use:
CONCURRENT_REQUESTS = 100
Increase Twisted IO thread pool maximum size¶
Currently Scrapy does DNS resolution in a blocking way with usage of thread pool. With higher concurrency levels the crawling could be slow or even fail hitting DNS resolver timeouts. Possible solution to increase the number of threads handling DNS queries. The DNS queue will be processed faster speeding up establishing of connection and crawling overall.
To increase maximum thread pool size use:
REACTOR_THREADPOOL_MAXSIZE = 20
Setup your own DNS¶
If you have multiple crawling processes and single central DNS, it can act like DoS attack on the DNS server resulting to slow down of entire network or even blocking your machines. To avoid this setup your own DNS server with local cache and upstream to some large DNS like OpenDNS or Verizon.
Reduce log level¶
When doing broad crawls you are often only interested in the crawl rates you
get and any errors found. These stats are reported by Scrapy when using the
INFO log level. In order to save CPU (and log storage requirements) you
should not use
DEBUG log level when preforming large broad crawls in
DEBUG level when developing your (broad) crawler may fine
To set the log level use:
LOG_LEVEL = 'INFO'
Retrying failed HTTP requests can slow down the crawls substantially, specially when sites causes are very slow (or fail) to respond, thus causing a timeout error which gets retried many times, unnecessarily, preventing crawler capacity to be reused for other domains.
To disable retries use:
RETRY_ENABLED = False
Reduce download timeout¶
Unless you are crawling from a very slow connection (which shouldn’t be the case for broad crawls) reduce the download timeout so that stuck requests are discarded quickly and free up capacity to process the next ones.
To reduce the download timeout use:
DOWNLOAD_TIMEOUT = 15
Consider disabling redirects, unless you are interested in following them. When doing broad crawls it’s common to save redirects and resolve them when revisiting the site at a later crawl. This also help to keep the number of request constant per crawl batch, otherwise redirect loops may cause the crawler to dedicate too many resources on any specific domain.
To disable redirects use:
REDIRECT_ENABLED = False
Enable crawling of “Ajax Crawlable Pages”¶
Some pages (up to 1%, based on empirical data from year 2013) declare themselves as ajax crawlable. This means they provide plain HTML version of content that is usually available only via AJAX. Pages can indicate it in two ways:
- by using
#!in URL - this is the default way;
- by using a special meta tag - this way is used on “main”, “index” website pages.
Scrapy handles (1) automatically; to handle (2) enable AjaxCrawlMiddleware:
AJAXCRAWL_ENABLED = True
When doing broad crawls it’s common to crawl a lot of “index” web pages; AjaxCrawlMiddleware helps to crawl them correctly. It is turned OFF by default because it has some performance overhead, and enabling it for focused crawls doesn’t make much sense.